CENTRAL PROCESSOR

• 1.6 GHz Intel^® Pentium^® M  processor:-

  • uses µFC-PGA 478 (micro Flip-Chip Pin Grid Array) package

  • 64 Kbytes of primary (L1) on-die cache

  • 1 Mbyte of secondary (L2) on-die cache

  • 400 MHz Front Side Bus (FSB)

  • no CPU fan

• 1.8 GHz or 1.4 GHz processor version (2 Mbytes L2 cache) available; see PP 302/02x-U datasheet

• utilizes 64-bit Intel^® 855GME chipset:-

  • supports 400 MHz bus frequency

  • uses Intel^® 6300ESB I/O Controller Hub

DRAM

• supporting up to 2 Gbytes 333 MHz DDR ECC SDRAM:-

  • up to 1 Gbyte soldered onboard

  • up to 1 Gbyte provided via a SODIMM socket

  • single bit error correction

• accessible from Pentium or CompactPCI bus

HARD DISK INTERFACES

• EIDE interface:-

  • supports Ultra-DMA 100 for high performance drives

  • two channels (primary and secondary)

  • secondary channel can be used for on-board 2.5 inch disk drive or, support for 1x (on-board socket) or 2x (using AD 200/001) CompactFlash or Microdrive™ Type II drives

  • primary channel is accessible via Transition Module

• Serial ATA150:-

  • two channels accessible via J5

  • transfer rate up to 150 Mbytes/s

• Ultra-320 Wide SCSI:-

  • accessible via Transition Module

  • implemented by an LSI 53C1020

ETHERNET INTERFACE

• four channels supporting 10 Base-T, 100 Base-TX,
  1000Base-T:-

  • front channels implemented by 2 x Intel^® 82541PI LAN controllers via 32-bit PCI bus

  • rear channels implemented by Intel^® 82546GB LAN Controller via 64-bit PCI bus

• 2 x channels accessed via J3 and 2 x channels via front panel RJ45 connectors

• support for PICMG 2.16 R1.0 - Packet Switched Backplane (PSB)

PMC (PCI MEZZANINE CARD) INTERFACE

• single PMC site:-

  • I/O via front panel

  • 32/64-bit, 33/66 MHz PCI operation

  • 3.3V signaling levels

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM - 8-bits wide

FIRMWARE SUPPORT

• Phoenix BIOS™

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

GRAPHICS INTERFACE

•  implemented by the Intel^® 855GME GMCH:-

  • resolutions up to 2048 x 1536 @75Hz

  • up to 16M colors

• accessed via a VGA connector on front panel or via J5

• DVI-D interface supported via J3

SOFTWARE SUPPORT

• support for  VxWorks^®, Linux^®, Windows NT^®, Windows^® XP Embedded, Windows^® 2000, Windows^® XP, Solaris^®, LynxOS^® and QNX^®

SERIAL INTERFACE

• 2 x RS232 serial channels:-

  • accessed by 2 x RJ45 connectors on front panel or via Transition Module

• each channel supports CTS, RTS, DSR, DTR and DCD via front panel and Transition Module; RI supported via Transition Module

• 16550 compatible UART

OTHER PERIPHERAL INTERFACES

• keyboard and mouse interfaces via a single PS/2™ type connector on front panel or via Transition Module

• PC-compatible RTC (Year 2000 compliant)

• floppy disk interface via Transition Module

• 3 x USB (Universal Serial Bus 2.0) interfaces:-

  • one via front panel

  • two via Transition Module

• watchdog timer

• system fan monitor; CPU temperature monitor; voltages monitor:-

  • all accessible via IPMI

• speaker interface

COMPACTPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels:-

  • universal signaling support

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors

• utilizes a PCI-PCI bridge for off-board accesses

• PICMG 2.1 R2.0 Hot Swap Specification

• operates as a System Slot controller or in a Peripheral Slot

• option to disable CompactPCI interface (Satellite Mode):-

  • receives power from CompactPCI bus

  • board can be hot swapped in this mode

• J4 connector not fitted

IPMI (INTELLIGENT PLATFORM MANAGEMENT INTERFACE)

•  PICMG 2.9 R1.0 (System Management Specification):-

  • implements the IPMB0 interface

  • implements an IPMB1 interface

• on-board Baseboard Management Controller

• supports 8 Kbytes of non-volatile memory

ELECTRICAL SPECIFICATION

• +5V@4.1A (typical with 1 Gbyte DRAM); +5% / -3%

•  +3.3V@1.9A; +5% / -3%

• +12V@0.05A; -12V@0.05A

• +12V and -12V routed to PMC expansion slot

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series)

• 10% to 90% Relative Humidity, non condensing (operating)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non condensing (storage)

MECHANICAL SPECIFICATION

•  6U form-factor: 9.2 inches x 6.3 inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:

  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);

  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)