- 2.0 GHz Intel^® Pentium^® M Processor 760 based Intelligent Dual PMC Carrier

CENTRAL PROCESSOR

• 2.0 GHz Intel® Pentium® M processor 760:-

  • 533 MHz Front Side Bus (FSB)

  • uses µFC-PGA 478
    (micro Flip-Chip Pin Grid Array) package

• 1.8 GHz Intel® Pentium® M processor 745:-

  • 400 MHz Front Side Bus (FSB)

  • uses mFC-PGA 478 package

• 1.4 GHz Intel® Pentium® M processor Low Voltage 738:-

  • 400 MHz Front Side Bus (FSB)

  • uses mFC-BGA 479
    (micro Flip-Chip Ball Grid Array) package

• common processor features are:-

  • 64 Kbytes of primary (L1) on-die cache

  • 2 Mbytes of secondary (L2) on-die cache

  • no CPU fan

• 1.6 GHz processor version available; see
  PP 310/01x-U datasheet

• utilizes 64-bit ServerWorks’ GC-LE chipset

• provision for ITP debug port

DRAM

• supporting up to 2 Gbytes DDR ECC SDRAM:-

  • up to 2 Gbytes via two SODIMM sockets

  • error correction up to 4-bits

• accessible from processor or CompactPCI bus

HARD DISK INTERFACES

• EIDE interface:-

  • supports up to Ultra-DMA 100 for high performance drives

  • two channels (primary and secondary)

  • secondary channel can be used for on-board 2.5 inch hard disk drive (in a single slot); or, support for 1 or 2 CompactFlash modules or Hitachi GST Microdrive™ Type II drives

  • primary channel accessed via Transition Module

ETHERNET INTERFACES

• implemented by Intel® 82546GB LAN Controller via 64-bit PCI bus supporting 10 Base-T, 100 Base-TX, 1000 Base-T

• two channels via J3:-

  • support for PICMG 2.16 R1.0 - Packet Switching Backplane (PSB)

  • optional support for rear panel RJ45’s via Transition Module

• one channel switchable to front panel RJ45

GRAPHICS INTERFACE

• implemented by a Silicon Motion SM722 providing:-

  • 8 Mbytes video memory

  • resolutions up to 1280 x 1024; supporting up to 16M colors

• accessed via a 26-way high-density connector on front panel

PMC INTERFACES

• 2 x PMC sites; for both sites:-

  • I/O via front panel

  • I/O via J3 and J5

  • 32/64-bit, 33/66 MHz PCI operation

  • 3.3V or 5V PCI signaling levels

  • Transition Module supports PMC rear I/O

FIRMWARE SUPPORT

• Phoenix® ServerBIOS™

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

BATTERY BACKED SRAM

• 512 Kbytes battery backed SRAM

SOFTWARE SUPPORT

• support for VxWorks, Windows NT, Windows 2000, Windows XP, Windows XP Embedded, QNX, Solaris and Linux

FLASH EPROMs

• 32 Mbytes of Application Flash EPROM - 8-bits wide

• 512 Kbytes of BIOS Flash EPROM - 8-bits wide

SERIAL INTERFACES

• up to 3 x RS232 serial channels:-

  • 1 channel via a 26-way high-density connector on front panel

  • either 1 channel via J5 or 2 channels via  optional Transition Module

• 16550 compatible UART

• supporting RI, CTS, RTS, DSR, DTR and DCD

OTHER PERIPHERAL INTERFACES

• keyboard and mouse interfaces accessed via a 26-way high-density connector on front panel

• PC-compatible Real Time Clock (Year 2000 compliant)

• watchdog timer

• system fan monitor; CPU temperature monitor; voltages monitor; all accessible via IPMI

• speaker interface

• 1 x USB (Universal Serial Bus) interface via J5 Transition Module

• 1 x 32-bit Long Duration Timer with processor interrupt capability

• LPC (Low Pin Count) bus via J5 to enable the
  AD PP5/001-U Transition Module support for:-

  • floppy disk interface

  • parallel printer port (ECP, EPP and IEEE1284)

  • 2 x RS232 serial channels

COMPACTPCI INTERFACE

• universal signaling support, compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors

• PCI-PCI bridge for off-board accesses

• PICMG 2.1 R2.0 Hot Swap compliant

• operates as a System Slot controller or in a Peripheral slot

• option to disable CompactPCI interface (Satellite Mode):-

  • receives power from CompactPCI bus

  • board can be hot swapped

• J4 connector not fitted

IPMI

• PICMG 2.9 R1.0 (System Management Specification)

• implements the IPMB0 interface

• on-board BMC (Baseboard Management Controller)

• supports 8 Kbytes of non-volatile memory

ELECTRICAL SPECIFICATION

• +5V@3.9A (typical at 1.8 GHz with 1 Gbyte DRAM); +5% / -3%

• +3.3V@6.5A; +5% / -3%

• +12V@0.01A; -12V@0.01A

• +12V and -12V routed to PMC slots

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperature:-

  • 0°C to +55°C (N-Series: up to 2.0 GHz)

  • -25°C to +70°C (E-Series: 1.4 GHz)

• 10% to 90% Relative Humidity, non-condensing (operating)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non-condensing (storage)

MECHANICAL SPECIFICATION

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:
  20g, 11ms, ½ sine (operating);
  30g, 11ms, ½ sine (non-operating)

• vibration:
  5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)