Specification Sheet: TP 302/32x
Intel® Pentium® M Processor 3U Single Board Computer

Due to component obsolescence, an End of Life (EOL) notification has been issued for this product. Please contact your local sales office for more information.

CENTRAL PROCESSOR

• 1.8 GHz Intel® Pentium® M Processor 745:-

  • using a µFC-PGA 478 (micro Flip-Chip Pin Grid Array) package

• 1.4 GHz Intel® Pentium® M processor Low Voltage 738:-

  • using a µFC-BGA 479 (micro Flip-Chip Ball Grid Array) package

• common processor features are:-

  • 64 Kbytes of primary (L1) on-die cache

  • 2 Mbytes of secondary (L2) on-die cache

  • 400 MHz Front Side Bus (FSB)

• utilizes 64-bit Intel® 855GME chipset:-

  • supports 400 MHz bus frequency

  • uses Intel® 6300ESB I/O Controller Hub

• provision for ITP debug port

DRAM

• 1 Gbyte 333 MHz DDR SDRAM soldered onboard

HARD DISK INTERFACES

• EIDE interfaces:-

  • supports up to Ultra-DMA 100 for high performance drives

  • single slot board supports on-board type I or type II CompactFlash site (not available on dual slot variants)

  • optional second slot boards supports type I or type II CompactFlash site, 2.5 inch disk drive and EIDE header for external drives

  • 2 interfaces available simultaneously

• 2 x Serial ATA150 interfaces:-

  • two channels accessible via J2

  • transfer rate up to 150 Mbytes/s

ETHERNET INTERFACES

• 2 x channels supporting 10 Base-T, 100 Base-TX, 1000 Base-T:-

  • implemented by Intel® 82546GB via 64-bit 66MHz PCI bus

• both channels accessed via front panel RJ45 connectors

STEREO AUDIO

• AC '97 interface via J2

• independent legacy speaker output via J2

• codec on rear transition module

GRAPHICS INTERFACE

• implemented by the Intel® 855GME GMCH:-

  • resolutions up to 2048 x 1536 @75Hz on analog interface

  • resolutions up to 1400 x 1050 @ 60Hz on DVI-D interface

  • up to 16M colors

• analog interface accessed via a 15-way VGA connector on front panel

• DVI-D interface accessed via J2

SERIAL INTERFACES

• 4 x serial channels:-

  • 1 x RS232 and 1 x RS232/422/485 channels accessible via front panel on optional second slot board

  • 2 x serial channels (TTL) accessible via J2

• 16550 compatible UARTs

• supporting RI, CTS, RTS, DSR, DTR and DCD

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM

• application storage available on CompactFlash card

FIRMWARE SUPPORT

• Phoenix™ BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

SOFTWARE SUPPORT

• supports Windows® 2000, Windows® XP, Windows® XP Embedded, QNX®, Linux® and VxWorks®

OTHER PERIPHERAL INTERFACES

• PC-compatible Real Time Clock (Year 2000 compliant)

• long duration timer

• watchdog timer

• CPU temperature monitor

• legacy speaker interface

• up to 4 x USB 2.0 interfaces:-

  • 1 via front panel

  • 1 via front panel on optional second slot board

  • 2 via J2

• PS/2 Keyboard and Mouse via single mini-DIN connector on optional second slot front panel

• 2 x GPIO signals via J2

COMPACTPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels:-

  • universal signaling support

• 33/66 MHz; 32-bit interface accessed via J1

• utilizing a PCI-PCI bridge for off-board accesses

• operates as a System Slot controller supporting up to 7 peripheral slots

• supports hot-swapping peripheral boards:-

  • PICMG 2.1 R2.0 Hot Swap Specification

ELECTRICAL SPECIFICATION

• +5V@3.4A (typical at 1.8 GHz with 1 Gbyte DRAM)

• +3.3V@3.3A (typical at 1.8 GHz with 1 Gbyte DRAM)

• +12V and -12V not required

• all voltages are tolerant to +5% / -3%

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: up to 1.8 GHz)

  • -25°C to +70°C (E-Series: 1.4 GHz)

  • -40°C to +85°C (K-Series: 1.4 GHz)

• 10% to 90% Relative Humidity, non-condensing (operating):-

  • K-Series includes humidity sealant

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non-condensing (storage)

MECHANICAL SPECIFICATION

• 3U form-factor: 3.9 inches x 6.3 inches (100mm x 160mm)

• single or dual slot

• connectors: IEC-1076-4-101 for J1-J2

• shock:
  20g, 11ms, ½ sine (operating);
  30g, 11ms, ½ sine (non-operating)

• vibration:
  5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)