Specification Sheet: FP 100/008 Switched Fabric Board

- 10/100Mbps Ethernet Switched Fabric Board

ETHERNET SWITCHED FABRIC

• 10-port 10/100Mbps Ethernet Switched Fabric board:-

  • compatible with PICMG^® 2.16 Packet Switched Backplane (PSB)

  • compatible with VITA 31.1 (Ethernet on VME64x backplanes)

  • 8 PSB Ethernet ports for PSB node boards

  • PSB Ethernet port for fabric to fabric link

  • front panel Ethernet port via RJ45

• high performance Ethernet Switched Fabric:-

  • implemented by Marvell^® 88E6083 single-chip switch

  • Layer 2 non-blocking fabric

  • 2048 MAC address cache with automatic learning and aging

  • full Virtual LAN (VLAN) support

•  auto-negotiation on all ports:-

  • 10/100Mbps

  • full/half duplex

• EEPROM storage for user configuration data

• 10/100/1000Mbps version available:-

  • see separate FP 110/008 datasheet

VIRTUAL LAN (VLAN)

• hardware based VLAN operation supporting:-

  • port-based membership

  • IEEE 802.1Q VLAN (up to 64 VLANs)

• offering security through:-

  • controlling group membership

  • providing Layer 2 firewall protection

QUALITY OF SERVICE (QoS)

• prioritized packet streams for management of voice, video and data

• 4 hardware priority queues per port

• fixed priority or weighted fair queuing

• QoS traffic classification, determined by:-

  • MAC address (SA or DA)

  • port ID

  • IEEE 802.1Q VLAN ID

  • IEEE 802.1p multimedia traffic tags

  • IPv4 Type of Service (TOS) or DiffServ

  • IPv6 Traffic Class

SYSTEM MANAGEMENT

• board health and status management:-

  • conforms to PICMG^® 2.9 R1.0 (System Management Specification)

  • implements the IPMB0 interface on J1

  • microcontroller-based Peripheral Management Controller

  • EEPROM for Field Replaceable Unit (FRU) and Sensor Data Record (SDR) storage

• network management:-

  • 40 statistics counters per port

  • SNMP support for Remote Monitoring (RMON)

  • IGMP snooping (IPv4)

  • MLD snooping (IPv6)

  • accessible via the IPMB0 interface

• hot swap insertion and removal

FRONT PANEL INTERFACES

• RJ45 connector for 10/100Mbps Ethernet User port

• speed and Link/Activity LEDs for all 10 Ethernet ports

• 1 user LED

• reset switch (recessed)

REAR PANEL INTERFACES

• compatible with CompactPCI^® Packet Switched Backplane (PSB):-

  • conforms to relevant sections of PICMG 2.16 R1.0

  • compatible with VITA 31.1 (Ethernet on VME64x backplanes)

• Ethernet port for linking 2 fabric boards:-

  • enables redundant fabric board or

  • increases the number of Ethernet ports in the system

• J1 and J3 connectors fitted as standard

ELECTRICAL SPECIFICATION

• +5V, +5%/-3% @ 0.1A

• +3.3V, +5%/-5% @ 0.6A

• +12V, +5%/-5% @ 0.01A

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperature:-

  • 0°C to +55°C (N-Series)

  • -25°C to +70°C (E-Series)

  • -40°C to +85°C (K-Series)

• 10% to 90% Relative Humidity, non-condensing (operating)

  • K-Series includes humidity sealant

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non-condensing (operating)

MECHANICAL SPECIFICATION

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1and J3

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:

  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating)

  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)