- 1.8 GHz Intel^® Pentium^® M Processor 745 or 1.4 GHz Intel^® Pentium^® M Processor 738 based Intelligent Dual PMC Carrier

CENTRAL PROCESSOR

• Two processor versions available

• 1.8 GHz Intel^® Pentium^® M processor 745:-

  • uses mFC-PGA 478 (micro Flip-Chip Pin Grid Array) package

• 1.4 GHz Intel^® Pentium^® M processor Low Voltage 738:-

  • uses mFC-BGA 479 (micro Flip-Chip Ball Grid Array) package

• Common processor features are:-

  • 64 Kbytes of primary (L1) on-die cache

  • 2 Mbytes of secondary (L2) on-die cache

  • 400 MHz Front Side Bus (FSB)

  • no CPU fan

• 1.6 GHz processor version (1 Mbyte L2 cache) available;
  see PP 330/02x-U datasheet

• utilizes 64-bit Intel^® 855GME chipset:-

  • supports 400 MHz bus frequency

  • uses Intel^® 6300ESB I/O Controller Hub

• provision for ITP debug port

DRAM

• supporting up to 2 Gbytes 333 MHz DDR ECC SDRAM:-

  • up to 2 Gbytes provided via two SODIMM sockets

  • single bit error correction

• accessible from Intel Pentium M processor or CompactPCI bus

HARD DISK INTERFACES

• EIDE interface:-

  • supports up to Ultra-DMA 100 for high performance drives

  • two channels (primary and secondary)

  • secondary channel supports on-board CompactFlash site

  • secondary channel can be used for on-board 2.5 inch disk drive (within a single slot); or, support for 1 or 2 CompactFlash or Microdrive™ Type II drives (in a single slot)

  • primary channel is accessible via Transition Module

  • on-board options use a PMC site

ETHERNET INTERFACES

• 4 x channels supporting 10 Base-T, 100 Base-TX,
  1000 Base-T:-

  • front panel implemented by 2 x Intel^® 82541PI via 32-bit 33MHz PCI bus

  • rear panel implemented by Intel^® 82546GB via 64-bit 33/66 MHz PCI bus

• 2 x channels accessed via J3 and 2 x channels via front panel RJ45 connectors:-

  • support for rear panel RJ45 connectors via Transition Module

• support for PICMG 2.16 R1.0 - Packet Switched Backplane (PSB)

PMC INTERFACES

• 2 x PMC sites; for both sites:-

  • I/O via front panel

  • I/O via J3 and J5

  • 32/64-bit, 33/66 MHz PCI operation

  • 3.3V signaling levels

• Transition Module provides rear I/O for both PMC sites

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM

FIRMWARE SUPPORT

• Phoenix™ BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

SERIAL INTERFACES

• up to 3 x RS232 serial channels:-

  • 1 channel via an onboard header (serial cable supplied)

  • 2 channels via optional Transition Module

• 16550 compatible UARTs

• channels support RI, CTS, RTS, DSR, DTR and DCD

SOFTWARE SUPPORT

• support for Windows^® 2000, Windows^® XP, Windows^® XP Embedded, VxWorks^®, QNX^® and Linux^®

OTHER PERIPHERAL INTERFACES

• PC-compatible Real Time Clock (Year 2000 compliant)

• watchdog timer

• system fan monitor; CPU temperature monitor; voltages monitor:-

  • all accessible via IPMI

• legacy speaker interface

• 3 x USB (Universal Serial Bus 2.0) interfaces:-

  • 2 via front panel

  • 1 via J5 Transition Module

• LPC (Low Pin Count) bus via J5 to enable AD PP5/001-U Transition Module to support:-

  • floppy disk interface

  • parallel printer port interface (ECP, EPP and IEEE1284)

  • 2 x RS232 serial channels

COMPACTPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels:-

  • universal signaling support

• J4 connector not fitted

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors

• utilizing a PCI-PCI bridge for off-board accesses

• PICMG 2.1 R2.0 Hot Swap Specification

• operates as a System Slot controller or in a Peripheral Slot

• option to disable CompactPCI interface (Satellite Mode):-

  • receives power from CompactPCI bus

  • board can be hot swapped in this mode

IPMI (INTELLIGENT PLATFORM MANAGEMENT INTERFACE)

• PICMG 2.9 R1.0 (System Management Specification):-

  • implements the IPMB0 interface

  • implements an IPMB1 interface

• on-board Baseboard Management Controller

• supports 8 Kbytes of non-volatile memory

ELECTRICAL SPECIFICATION

• +5V@3.5A (typical at 1.8 GHz with 1 Gbyte DRAM); +5% / -3%

• +3.3V@2.0A; +5% / -3%

• +12V@0.05A; -12V@0.05A

• +12V and -12V routed to PMC slots

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: 1.8 GHz, 1.4 GHz)

  • -25°C to +70°C (E-Series: 1.4 GHz)

  • -40°C to +85°C (K-Series: 1.4 GHz)

• 10% to 90% Relative Humidity, non-condensing (operating):-

  • K-Series includes humidity sealant

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non-condensing (storage)

MECHANICAL SPECIFICATION

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:

  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);

  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)