CENTRAL PROCESSOR

• 2.16 GHz Intel® Core™ 2 Duo processor T7400:-

  • uses mFC-PGA 478
    (micro Flip-Chip Pin Grid Array) package

• 1.5 GHz Intel® Core™ 2 Duo processor L7400:-

  • uses mFC-BGA 478
    (micro Flip-Chip Ball Grid Array) package

• common processor features are:-

  • dual-core processor

  • 667 MHz Front Side Bus

  • 64 Kbytes of primary (L1) on-die cache

  • 4 Mbytes of secondary (L2) on-die cache

  • Intel® 64 Technology (64-bit computing) support

  • no CPU fan; low power processor

• utilizes 64-bit Intel® 945GME Express chipset:-

  • uses Intel® ICH7-M DH Controller Hub

DRAM

• supporting up to 4 Gbytes 667 MHz DDR2 SDRAM:-

  • single channel or dual channel operation

  • 2 Gbytes soldered onboard giving peak bandwidth of up to 5.3 Gbytes/s

  • 4 Gbytes (SODIMM + soldered) giving peak bandwidth of up to 10.6 Gbytes/s

• accessible from processor or CompactPCI bus

HARD DISK INTERFACES

• 1 x EIDE interface:-

  • supports 1x CompactFlash™ or Microdrive™ Type II drive using on-board socket

• 2 x Serial ATA150 interfaces:-

  • both channels accessible via J5 to the Rear Transition Module (RTM)

  • one channel switchable to on-board SATA disk drive (in a single slot)

  • transfer rate up to 150 Mbytes/s

ETHERNET INTERFACES

• four channels supporting 10 Base-T, 100 Base-TX, 1000Base-T

• 2 x front panel interfaces accessed via RJ45 connectors:-

  • implemented by 2 x Intel® 82541PI LAN controllers via 32-bit, 33 MHz PCI Bus

• 2 x rear interfaces accessed via J3:-

  • implemented by 2 x Intel® 82573L LAN controllers via x1 PCI Express® links

• support for PICMG 2.16 R1.0 - Packet Switched Backplane (PSB)

PMC INTERFACE

• single PMC site:-

  • I/O via front panel and J5

  • 32/64-bit, 33/66/100 MHz PCI/PCI-X operation

  • 3.3V PCI signaling levels

GRAPHICS INTERFACE

• implemented by the Intel® 945GM Express:-

  • resolutions up to 2048 x 1536 @ 75Hz

  • up to 16M colors

• accessed via a 15-way high density connector on front panel or via J3 (DVI-A)

• DVI-D interface supported via J3

• DVI-I connector available on Transition Module

SERIAL INTERFACES

• 2 x RS232 serial channels:-

  • accessed by 2 x RJ45 connectors on front panel or via J3/J5

• each channel supports CTS, RTS, DSR, DTR and DCD via front panel and Transition Module; RI supported via Transition Module

• 16550 compatible UART

OTHER PERIPHERAL INTERFACES

• keyboard and mouse interfaces via a single PS/2™ type connector on front panel or via J3

• PC-compatible RTC (Year 2000 compliant)

• 4 x USB (Universal Serial Bus 2.0) interfaces:-

  • one via front panel

  • three via J5

• watchdog timer; long duration timer

• system fan monitor; CPU temperature monitor; voltages monitor:-

  • all accessible via IPMI

• legacy speaker interface

SOFTWARE SUPPORT

• support for Linux®, Windows® XP Embedded, Windows® 2000, Windows® XP, Windows® Server 2003, Solaris™, LynxOS®, QNX® and VxWorks®

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM - 8-bits wide

• 1 Mbyte of Flash EPROM

• application storage available in CompactFlash

FIRMWARE SUPPORT

• Phoenix® TrustedCore™ BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

IPMI INTERFACE

• PICMG 2.9 R1.0 (System Management Specification):-

  • implements the IPMB0 interface

  • implements an IPMB1 interface

• on-board Baseboard Management Controller

• supports 8 Kbytes of non-volatile memory

CompactPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels (universal signaling support)

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors

• utilizes a PCI-X to PCI bridge for off-board accesses

• PICMG 2.1 R2.0 Hot Swap Specification

• operates as a System Slot controller or in a Peripheral Slot

• option to disable CompactPCI interface (Satellite Mode):-

  • receives power from CompactPCI bus

  • board can be hot swapped in this mode

• J4 connector not fitted

ELECTRICAL SPECIFICATION

• typical at 2.16 GHz with 2 Gbytes DRAM

  • +5V@4.9A; +5% / -3%

  • +3.3V@2.7A; +5% / -3%

  • +12V@0.05A; -12V@0.05A

• +12V and -12V routed to PMC expansion slot

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: 2.16 GHz, 1.5 GHz)

  • -25°C to +70°C (E-Series: 1.5 GHz)

  • -40°C to +85°C (K-Series: 1.5 GHz)

• 10% to 90% Relative Humidity, non condensing (operating)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non condensing (storage)

MECHANIAL SPECIFICATION

• 6U form-factor: 9.2 inches x 6.3 inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:
  20g, 11ms, ½ sine (operating);
  30g, 11ms, ½ sine (non-operating)

• vibration:
  5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)