CENTRAL PROCESSORS

• dual processors; for each processor:-

  • 1.66 GHz Dual-Core Intel® Xeon® processor ULV

  • internal primary (L1) on-die cache

  • 2 Mbytes secondary (L2) shared on-die cache

  • Intel® Core™ Microarchitecture

• no CPU fan required

• utilizes 64-bit Intel® E7520 chipset:-

  • supports 667 MHz processor bus to give peak bandwidth of 5.3 Gbytes/s

  • uses Intel® 6300ESB I/O Controller Hub

DRAM

• supports up to 8 Gbytes DDR2-400 ECC SDRAM:-

  • up to 4 Gbytes soldered to board

  • up to 4 Gbytes provided via two 200-pin SODIMM sockets

  • dual channel configuration

  • peak bandwidth of 6.4 Gbytes/s

  • error correction up to 4-bits

• accessible from processors and CompactPCI bus

HARD DISK INTERFACES

• EIDE interface:-

  • supports up to Ultra-DMA 100 for high performance drives

  • 2 x channels (primary and secondary)

  • secondary channel can be used for on-board 2.5 inch disk drive or up to 2 CompactFlash™ or Microdrive™ Type II drives

  • on-board options occupy the PMC site

  • primary channel accessed via J3 to the Transition Module

• Serial ATA interfaces:-

  • 2 x channels accessible via J5

  • transfer speeds up to 150 Mbytes/s

ETHERNET INTERFACES

• 4 x channels supporting 10Base-T, 100Base-TX, 1000Base-T

• front panel interfaces:-

  • implemented by an Intel® 82571EB LAN controller via a x4 PCI Express™ link

  • accessed via front panel RJ45 connectors

• rear I/O interfaces:-

  • implemented by 2 x Intel® 82573L LAN controllers via x1 PCI Express links

  • support for PICMG 2.16 - Packet Switching Backplane (PSB)

  • optional support for rear panel RJ45’s via J3 to the Transition Module

GRAPHICS INTERFACE

• implemented by a Silicon Motion SM722:-

  • 8 Mbytes video memory

  • resolution up to 1280 x 1024 @ 16M colors

• analog interface via front panel connector

• DVI-D interface supported via J3

PMC INTERFACE

• 1 x PMC site:-

  • 3.3V signaling

  • supports 32/64-bit, 33/66 MHz PCI and
    66 MHz PCI-X operation

  • XMC (PCI Express Mezzanine Card) interface supported via x8 or dual x4 PCI Express Link

• I/O via front panel and via J5:-

  • Transition Module supports rear I/O

SERIAL INTERFACES

• 2 x RS232 serial channels:-

  • one channel accessed via J3 to the Transition Module and front panel

  • one channel accessed via J5 to the Transition Module

• 16550 compatible UART

• supports CTS, RTS, RI, DSR, DTR and DCD

OTHER PERIPHERAL INTERFACES

• keyboard and mouse interfaces, sharing a single PS/2™ type connector on front panel and accessible via J3 to the Transition Module

• PC-compatible Real Time Clock (Year-2000 compliant)

• 3 x USB 2.0 interfaces accessed via J5 to the  Transition Module

• 1 x USB 2.0 interface via front panel

• watchdog timer

• system fan monitor; two CPU temperature monitors; voltages monitor; board temperature monitor:-

  • all accessible via IPMI

• legacy speaker interface

COMPACTPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V and 5V signaling levels:-

  • universal signaling supported

• 33/66 MHz; 32/64-bit interface accessed via J1/J2 connectors

• utilizing a PCI-X to PCI bridge for off-board accesses

• PICMG 2.1 R2.0 Hot Swap Specification Compatible as hot swap controller only

• J4 connector not fitted

• operates as a System Slot controller or in a peripheral slot

• option to disable CompactPCI interface (Satellite Mode):-

  • use in any slot

  • receives power from CompactPCI bus

  • board can be hot swapped in this mode

FIRMWARE SUPPORT

• Phoenix® TrustedCore™

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM - 8-bits wide

SOFTWARE SUPPORT

• support for Linux®, Windows® Server 2003, Windows® XP, Windows® 2000, QNX®, Solaris™ and LynxOS®

IPMI

• PICMG 2.9 R1.0 (System Management Specification)

• implements the IPMB0 and IPMB1 interfaces

• on-board Baseboard Management Controller

• supports 32 Kbytes of non-volatile memory

ELECTRICAL SPECIFICATION

• +5V@4.0A (typical with 2 Gbytes DRAM); +5% / -3%

• +3.3V@7.0A; +5% / -3%

• +12V@0.02A; -12V@0.01A

• +12V and -12V routed to PMC expansion slot

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• 0°C to +55°C (operating)

• 10% to 90% Relative Humidity (operating non-condensing)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity (storage non-condensing)

MECHANICAL SPECIFICATION

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)

• single-slot: 0.8 inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:
  20g, 11ms, ½ sine (operating);
  30g, 11ms, ½ sine (non-operating)

• vibration:
  5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)