CENTRAL PROCESSOR

• 2.16 GHz Intel® Core™ 2 Duo processor T7400:-

  • uses mFC-PGA 478 (micro Flip-Chip Pin Grid Array) package

• 1.5 GHz Intel® Core™ 2 Duo processor L7400:-

  • uses mFC-BGA 478 (micro Flip-Chip Ball Grid Array) package

• common processor features are:-

  • dual-core CPU

  • 4 Mbytes of secondary (L2) on-die cache

  • 667 MHz Front Side Bus

  • 64 Kbytes of primary (L1) on-die cache

  • Intel® 64 (or Intel® EM64T) 64-bit computing support

  • no CPU fan; low power processor

• utilizes Intel® 3100 server class chipset:-

  • supports 667 MHz processor bus to give peak bandwidth of 5.3 Gbytes/s

  • single chip combining memory and I/O controllers

• provision for XDP debug port

DRAM

• supports up to 4 Gbytes DDR2-400 ECC SDRAM:-

  • up to 4 Gbytes via two SODIMM sockets

  • single bit error correction

  • supports single channel memory to give a peak bandwidth of 3.2 Gbytes/s

• accessible from processor or CompactPCI bus

HARD DISK INTERFACES

• 4 x SATA-150 interfaces:-

  • 2 channels accessible via J5

  • optional 2.5 inch SATA hard disk drive assemblies in a single slot (uses PMC site)

  • support for CompactFlash™ site under PMC site via SATA to PATA convertor

ETHERNET INTERFACES

• 4 x channels supporting 10 Base-T, 100 Base-TX, 1000 Base-T

• 2 x front panel interfaces implemented by two Intel® 82573L, accessed via front panel RJ45's

• 2 x rear interfaces implemented by
  Intel® 82546GB controller:-

  • support for PICMG 2.16 R1.0 - Packet Switching Backplane (PSB)

  • optional support for rear panel RJ45’s via J3

PMC INTERFACES

• 2 x PMC sites

• for PMC site 1:-

  • 32-bit, 33 MHz PCI operation

  • 3.3V or 5V PCI signaling levels

  • I/O via front panel and via J5

• for PMC site 2:-

  • 32/64-bit, 33/66/100 MHz PCI/PCI-X operation

  • 3.3V PCI signaling level

  • I/O via front panel and via J3

• common features for both PMC sites:-

  • XMC (PCI Express® Mezzanine Card) interface supported via x1 PCI Express Link

  • I/O via front panel and via J3/J5

  • Transition Modules support rear I/O

SERIAL INTERFACES

• 2 x RS232 Tx/Rx serial channels; either:-

  • 1 accessed via on-board header and 1 via J5

  • or 2 via LPC (Low Pin Count) bus on J5 to optional AD PP5/001-40U Rear Transition Module

• 16550 compatible UARTs

• rear panel supports CTS, RTS

OTHER PERIPHERAL INTERFACES

• PC Real Time Clock (Year 2000 compliant)

• watchdog timer

• 1 x 32-bit Long Duration Timer with processor interrupt capability

• system fan monitor; CPU temperature monitor; voltages monitor:-

  • accessible via IPMI

• 4 x USB 2.0 interfaces:-

  • 2 via front panel

  • 2 via J5

• independent legacy speaker output via J3

• LPC (Low Pin Count) bus via J5 to enable the
  AD PP5/001 Transition Module support for:-

  • floppy disk interface

  • parallel port interface (ECP, EPP, IEEE1284)

  • 2 x RS232 serial channels

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM - 8-bits wide

FIRMWARE SUPPORT

• Phoenix® TrustedCore™ Server BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

SOFTWARE SUPPORT

• support for Linux®, Windows® XP, Windows® 2000, Windows® XP Embedded, Windows® Server 2003, QNX® VxWorks® and Solaris™

IPMI

• PICMG 2.9 R1.0 (System Management Specification):-

  • implements the IPMB0 interface

  • implements an IPMB1 interface

• on-board Baseboard Management Controller

• supports 8 Kbytes of non-volatile memory

CompactPCI INTERFACE

• compliant with PICMG 2.0 R3.0; 3.3V or 5V signaling levels (universal signaling support)

• 33/66 MHz, 32/64-bit interface accessed via J1/J2 connectors

• PCI-X to PCI bridge for off-board accesses

• J4 connector not fitted

• PICMG 2.1 R2.0 Hot Swap compliant

• operates as a System Slot controller or in a Peripheral slot

• option to disable CompactPCI interface (Satellite Mode):-

  • receives power from CompactPCI bus

  • board can be hot swapped

ELECTRICAL SPECIFICATION

• typical at 2.16 GHz with 1 Gbyte DRAM

  • +5V@6.8A; +5% / -3%

  • +3.3V@3.7A; +5% / -3%

  • +12V@0.05A; -12V@0.05A

• +12V and -12V routed to PMC slots

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ENVIRONMENTAL SPECIFICATION

• operating temperature:-

  • 0°C to +55°C (N-Series)

  • -25°C to +70°C (E-Series: 1.5 GHz)

• 10% to 90% Relative Humidity, non-condensing (operating)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non-condensing (storage)

MECHANICAL SPECIFICATION

• 6U form-factor: 9.2inches x 6.3inches (233mm x 160mm)

• single-slot: 0.8inches (20.3mm)

• connectors: IEC-1076-4-101 for J1-J5

• shock:
  20g, 11ms, ½ sine (operating);
  30g, 11ms, ½ sine (non-operating)

• vibration:
  5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)