- 1.6 GHz or 1.1 GHz Intel^® Pentium^® M Processor based Dual PMC Embedded Controller

CENTRAL PROCESSOR

• Intel^® Pentium^® M Processor operating at
  1.6 GHz:-

  • 1.6 GHz uses µFC-PGA 478
    (micro Flip-Chip Pin Grid Array) package

  • 64 Kbytes of primary (Level 1) on-die cache

  • 1 Mbyte of secondary (Level 2) on-die cache

  • 400 MHz Front Side Bus (FSB)

• 1.8 GHz or 1.4 GHz processor versions available;
  see VP 317/02x-U datasheet

• no CPU fan

• utilizes 64-bit Intel^® 855GME chipset:-

  • supports 400 MHz bus frequency

• utilizes Intel^® 6300ESB I/O Controller Hub

• ITP debug port

DRAM

• 1 Gbyte of 266 MHz DDR ECC SDRAM soldered on the board

• single bit error correction; double-bit error detection

• accessible from processor or VME bus

HARD DISK INTERFACES

• supports up to Ultra-DMA 100 for high performance drives

• two channels (primary and secondary)

• primary channel is accessible via P2 connector:-

  • connects to an optional hard disk/flash/CD-ROM drive board

• secondary channel can be used for on-board disk drive or dual CompactFlash/MicroDrive Type II drive carrier

SERIAL ATA INTERFACE

• Serial ATA (SATA) interface:-

  • one SATA port via P0

• supports up to 150 Mbytes/s transfer rates

ETHERNET INTERFACE

• implemented by Intel^® 82546GB LAN Controller via
  64-bit/66 MHz PCI bus

•  two interfaces supporting 10Base-T, 100Base-TX,
  1000Base-T:-

  • both interfaces accessed via optional P0

  • one channel switchable to front panel RJ45

• support for VITA 31.1 -

  • Gigabit Ethernet for VME64x backplanes

GRAPHICS INTERFACE

• implemented by the Intel^® 855GME GMCH host bridge providing:-

  • resolutions up to 2048 x 1536 @75Hz

  • up to 16M colors

• accessed via a 26-way high-density connector on front panel

• analog graphics interface supported via optional P0

PMC (PCI MEZZANINE CARD) INTERFACE

• 2 x PMC sites and for both sites:-

  • I/O via front panel, via P2 for site 1 (see Note 2) and optionally via P0 for site 2

  • 32/64-bit and 33/66 MHz PCI operation

  • 3.3V PCI signaling

• expansion to an optional dual PMC carrier board:-

  • using expansion connector (32-bit/33 MHz)

  • or using one baseboard PMC site (64-bit/66 MHz)

SERIAL INTERFACE

• 3 x serial channel interfaces

• 16550 compatible UART

• front panel access:-

  • 1 x RS232 via 26-way high density connector

•  rear panel access:-

  • 2 x RS232/422/485, both via P2 (see Note 2)

SOFTWARE SUPPORT

• support for VxWorks^®, Linux^®, Windows^® NT, Windows^® 2000, Windows^® XP, Windows^® XP Embedded, RTX^®, QNX^®, Solaris^™, LynxOS^® and MS-DOS^®

FLASH EPROM

• 64 Mbytes Application Flash EPROM

• 512 Kbytes of BIOS Flash EPROM

FIRMWARE SUPPORT

• Phoenix^® BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

OTHER PERIPHERAL INTERFACES

• PC-compatible Real Time Clock (Year 2000 compliant)

• 2 x USB 2.0 interfaces, one via P2 connector and one via optional P0

• keyboard and mouse interfaces accessed via a 26-way high-density connector on front panel and optionally via P0 connector

• watchdog timer

• 1 x 32-bit Long Duration Timer with processor interrupt capability

VME INTERFACE

• implemented using Tundra^® Universe II™ device

• VME Master/Slave

• A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64

• fast hardware byte swapping

• auto system controller detect

• full interrupter / interrupt handler support

• bus error interrupt hardware

ELECTRICAL SPECIFICATION

• +5V@4.1A (typical at 1.6 GHz with 1 Gbyte DRAM)

• +12V@0A; -12V@0A

• +12V and -12V routed to both PMC sites and PMC expansion connector

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: 1.6 GHz)

• 10% to 90% Relative Humidity, non condensing (operating):-

  • K-Series includes humidity sealant

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non condensing (storage)

• ruggedized versions available, see separate datasheets:-

  • air cooled: VP 315/022-RA

  • conduction cooled: VP 315/022-RC

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

MECHANICAL SPECIFICATION

• 6U form-factor

• single VME slot - front panel width 0.8inch (20.3mm)

• utilizes 160-way DIN connectors for P1 and P2:-

  • compatible with normal 96-way DIN connectors

• optional P0 (optional for VME64x backplanes only)

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:

  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating); 

  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)

Note 1: specific variants are supplied with VME64x handles

Note 2: 5-row backplane is required to provide P2 access to
2 x RS232/422/485 interfaces and full 64-bit PMC I/O for PMC
site 1