- 1.6 GHz Intel^® Pentium^® M Processor based Single Board Computer

CENTRAL PROCESSOR

• 1.6 GHz Intel^® Pentium^® M processor:-

  • uses mFC-PGA 478 (micro Flip-Chip Pin Grid Array) package

  • 64 Kbytes of primary (L1) on-die cache

  • 1 Mbyte of secondary (L2) on-die cache

  • 400 MHz Front Side Bus (FSB)

  • no CPU fan

• 1.8 GHz or 1.4 GHz processor version (2 Mbytes L2 cache) available; see VP 327/02x-U datasheet

• utilizes 64-bit Intel^® 855GME chipset:-

  • supports 400 MHz bus frequency

  • uses Intel^® 6300ESB I/O Controller Hub

• ITP debug port

DRAM

•  supporting up to 2 Gbytes 333 MHz DDR ECC SDRAM:-

  • 1 Gbyte soldered onboard

  • up to 1 Gbyte provided via SODIMM socket

  • single bit error correction

• accessible from processor or VME bus

HARD DISK INTERFACES

• EIDE interface:-

  • accessed via P2 connector

  • supports up to Ultra-DMA 100 for high performance drives

  • two channels (primary and secondary)

  • primary channel is accessible via P2 connector

  • secondary channel can be used for on-board 2.5 inch disk drive or CompactFlash module or Microdrive Type II drive (the board still fits in a single slot). Does not use PMC site

  • connects to an optional Mass Storage Module (DS MSS/IFP, DS MSS/00x)

• 2 x Serial ATA150 channels:-

  • both via optional P0 connector

  • transfer rate up to 150 Mbytes/s

ETHERNET INTERFACE

• 2 x channels supporting 10 Base-T, 100 Base-TX,
  1000Base-T:-

  • implemented by Intel^® 82546GB LAN Controller via 64-bit PCI bus

• accessed via front panel RJ45 connectors

GRAPHICS INTERFACE

• implemented by the Intel^® 855GME GMCH:-

  • resolutions up to 2048 x 1536 @75Hz

  • up to 16M colors

• accessed via a front panel connector

• flat panel supported using DVI via P2 connector:-

  • when ordered for a 3-row backplane the supplied breakout uses a DFP connector

  • when ordered for a 5-row backplane the supplied breakout uses a DVI-D connector

STEREO AUDIO (See Note 2)

• line level output pair via P2 connector

• line level input pair via P2 connector

• independent legacy speaker output via P2

SERIAL INTERFACE

• 4 x RS232 serial interfaces:-

  • 2 x RS232 via RJ45 connectors on front panel

  • 2 x RS232 via P2 connector (see Note 2)

  • 16550 compatible UARTs

PMC (PCI MEZZANINE CARD) INTERFACE

• one PMC slot with I/O via front panel and optionally via P0:-

  • 32/64-bit, 33/66 MHz PCI operation

  • 3.3V or 5V signaling levels

  • still available when EIDE drive option fitted

• provides expansion connector to a PMC carrier board with two additional 32-bit, 33MHz PMC sites

SOFTWARE SUPPORT

• support for VxWorks^®, Windows^® NT, Windows^® 2000,  Windows^® XP, Windows^® XP Embedded, RTX^®, Linux^®, Solaris^™, LynxOS^®, QNX^® and MS-DOS^®

OTHER PERIPHERAL INTERFACES

• 4 x USB 2.0 (Universal Serial Bus) interfaces:-

  • 1 x USB via front panel connector

  • 3 x USB via P2 connector (see Note 2)

• keyboard and mouse interfaces via a single PS/2™ type connector on front panel

• PC-compatible Real Time Clock (Year 2000 compliant)

• floppy disk interface via P2 connector

• parallel printer port interface (ECP, EPP and IEEE1284) via P2 connector

• watchdog timer

• 1 x 32-bit Long Duration Timer with processor  interrupt capability

VME INTERFACE

•  implemented by Tundra^® Universe II™ device

• VME Master/Slave

• A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64

• fast hardware byte swapping

• auto system controller detect

•  full interrupter / interrupt handler support

• bus error interrupt hardware

FLASH EPROM

• 1 Mbyte of BIOS Flash EPROM

FIRMWARE SUPPORT

• Phoenix^® BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

ELECTRICAL SPECIFICATION

• +5V@4.8A (typical at 1.6 GHz with 1 Gbyte DRAM)

• +12V@0.1A; -12V@0.0A

• +12V and -12V routed to both PMC sites and PMC expansion connector

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: 1.6 GHz)

• 10% to 90% Relative Humidity, non condensing (operating)

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non condensing (storage)

MECHANICAL SPECIFICATION

• 6U form-factor

• single slot - width 0.8inch (20.3mm)

• utilizes 160-way DIN connectors for P1 and P2:-

  • compatible with 96-way DIN connectors

• optional P0 (for VME64x backplanes only)

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:

  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);

  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)

Note 1: selected variants are supplied with VME64x handles

Note 2: 5-row backplane is required to provide P2 access to RS232, USB, stereo audio line input, stereo audio line output and legacy speaker interfaces