- 1.6 GHz Intel® Pentium® M or 1.0 GHz Intel® Celeron® M Processor Dual PMC Embedded Controller

CENTRAL PROCESSOR

• 1.6 GHz Intel® Pentium® M processor:-

  • using a µFC-PGA 478
    (micro Flip-Chip Pin Grid Array) package

  • 1 Mbyte of secondary (L2) on-die cache

• 1.0 GHz Intel® Celeron® M processor Ultra Low Voltage 373:-

  • using a µFC-BGA 479
    (micro Flip-Chip Pin Grid Array) package

  • 512 Kbytes of secondary (L2) on-die cache

• common processor features are:-

  • 64 Kbytes of primary (L1) on-die cache

  • 400 MHz Front Side Bus (FSB)

  • no CPU fan

• 1.8 GHz and 1.4 GHz processor versions
  (2 Mbytes L2 Cache) available; see VP 337/02x-U datasheet

• no CPU fan

• utilizes 64-bit Intel® 855GME chipset:-

  • supports 400 MHz bus frequency

• utilizes Intel® 6300ESB I/O Controller Hub

• ITP debug port

DRAM

• supporting up to 1 Gbyte of 333 MHz DDR ECC SDRAM soldered on the board

• single bit error correction; double-bit error detection

• accessible from processor or VME bus

EIDE HARD DISK INTERFACES

• supports up to Ultra-DMA 100 for high
  performance drives

• two channels (primary and secondary)

• primary channel is accessible via P2
  connector (see note 2):-

  • connects to an optional
    hard disk/flash/CD-ROM drive board

• secondary channel can be used for on-board disk drive or dual CompactFlash/MicroDrive Type II drive carrier

ETHERNET INTERFACE

• implemented by Intel® 82546GB LAN Controller via 64-bit/66 MHz PCI bus

• supporting 10Base-T, 100Base-TX and 1000Base-T:-

  • accessed via front panel RJ45

GRAPHICS INTERFACE

• implemented by the Intel® 855GME GMCH host bridge providing:-

  • resolutions up to 2048 x 1536 @75Hz

  • up to 16M colors

• VGA interface accessed via a 26-way high-density connector on front panel

PMC INTERFACES

• 2 x PMC sites and for both sites:-

  • I/O via front panel, via P2 for site 1 and optionally via P0 for site 2

  • 32/64-bit and 33/66 MHz PCI operation

  • 3.3V or 5V PCI signaling

• expansion to optional dual PMC carrier board:-

  • using expansion connector (32-bit/33 MHz)

  • or using one baseboard PMC site (64-bit/66 MHz)

SERIAL INTERFACE

• 1 x serial channel interface

• 16550 compatible UART

• front panel access:-

  • 1 x RS232 via 26-way high density connector

FLASH EPROM

• 64 Mbytes Application Flash EPROM

• 512 Kbytes of BIOS Flash EPROM

OTHER PERIPHERAL INTERFACES

• PC-compatible Real Time Clock (Year 2000 compliant)

• floppy disk interface via P2 connector (see note 2)

• 1 x USB 2.0 interface via P2 connector (see note 2)

• keyboard and mouse interfaces accessed via a 26-way high-density connector on front panel

• watchdog timer

• 1 x 32-bit Long Duration Timer with processor interrupt capability

SOFTWARE SUPPORT

• support for VxWorks®, Linux®, Windows NT®, Windows® 2000, Windows® XP Embedded, Windows® XP, RTX®, QNX®, Solaris™, LynxOS® and MS-DOS®

FIRMWARE SUPPORT

• Phoenix® BIOS

• comprehensive Power-On Self-Test (POST)

• LAN boot firmware included

VME INTERFACE

• implemented by Tundra® Universe II™ device

• VME Master/Slave

• A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64

• fast hardware byte swapping

• auto system controller detect

• full interrupter / interrupt handler support

  • bus error interrupt hardware

SAFETY

• PCB (PWB) manufactured with flammability rating of 94V-0

ELECTRICAL SPECIFICATION

• +5V@4.1A (typical at 1.6 GHz with 1 Gbyte DRAM)

• +12V@0A; -12V@0A

• +12V and -12V routed to both PMC sites and PMC expansion connector

ENVIRONMENTAL SPECIFICATION

• operating temperatures:-

  • 0°C to +55°C (N-Series: up to 1.6 GHz)

  • -25°C to +70°C (E-Series: 1.0 GHz)

  • -40°C to +85°C (K-Series: 1.0 GHz)

• 10% to 90% Relative Humidity, non condensing (operating):-

  • K-Series includes humidity sealant

• -40°C to +85°C (storage)

• 10% to 90% Relative Humidity, non condensing (storage)

MECHANICAL SPECIFICATION

• 6U form-factor

• single VME slot - front panel width 0.8inch (20.3mm)

• utilizes 160-way DIN connectors for P1
  and P2:-

  • compatible with normal 96-way DIN connectors

• optional P0 (for VME64x backplanes only)

• shock:

  • 20g, 11ms, ½ sine (operating);

  • 30g, 11ms, ½ sine (non-operating)

• vibration:
  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating);
  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)

Note 1: selected variants are supplied with VME64x handles

Note 2: 5-row backplane is required to provide P2 access to USB, EIDE and floppy disk interfaces